In this article below you'll find additional amazing advice pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging project. If the old tub is readily obtainable, the job can move quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old tub and set in the brand-new one. See to it you have qualified yourself for the work and are comfortable trying it. Rather than employing a specialist to take over a halfway-completed job, it is much better to consider utilizing one prior to you start. Chances are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new bathtub in your restroom if you have actually already bought a brand-new tub and do not require to alter the setup of your previous water supply pipes.
Your devices and material list should make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite bothersome as a result of the limited accessibility that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipelines. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in area in between the faucet and also the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind should be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of both wood boards under its feet, put the bath tub in the called for position. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub till the spirit level reads level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the water as well as check all joints as well as brand-new pipework for leaks and tighten them if essential. Fill up the tub and also examine the overflow electrical outlet and the typical electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has actually been used at the very least once as this will settle it right into its final setting.
Preparing for the Setup
Firstly, the supporting framework supplied with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to stop pressure on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to fracture an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, resulting in issues with wetness as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the motion experienced when the tub is in usage. The sealant can fracture relatively early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the floor tiles making use of waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on Installing A Bathtub? Make a remark down the page. We'd be delighted to find out your responses about this posting. We are looking forward that you come back again in the future. Sharing is caring. One never knows, you could be doing someone a favor. Thank you for your time invested reading it.
Free Estimates